MapleEngineer

"I can't be a racist sack of shit and spew hate speech in Canada so I'm not coming!" - a fetid sack of gangrenous anal sphincters.

And yet they are braying for Trump Lite who is playing directly from the US christofascist playbook of grievance and identity politics while making impossible promises without ever telling us how he plans to deliver. But, he's"not Trudeau" amiright?

Danielle Smith, a white supremacist supported christofascist who has talked about putting progressive politicians, "in the cross hairs" can choke on a fucking horse dick.

Apparently Polievre's grievance politics don't play very well to an audience with actual grievances.

Remember that these are the guys who said that they were preparing to fight UN and/or Chinese troops who might invade Canada?

Now their lawyer says that they were used for hunting? Was she taking about the pipe bomb or the handguns?

I don't see a single trigger or cable lock in that photo. Was the ammunition stored in a separate locked container?

These guys should never be allowed to own a firearm again based solely on the UN/China delusion. These types of violent collective fantasies are extremely dangerous and they absolutely should be disqualifying.

This guy is seriously delusional.

Olienick rejects the allegation he would threaten officers, but qualifies it by saying, "unless you guys are shooting at us first."

"But it wouldn't be you guys," he adds. "It would be UN guys or Chinese."

The UN and/or China are going to invade Canada?

Seriously?

"I'm not going to be the first guy who's going to do it. I'm going to be the guy that's going to end it if it happens."

These people watch way to fucking many US made one hero goes on a killing rampage and saves the day movies. Remember Ashli Babbitt? She and her angry mob were going to overthrow the US government and hang Mike Pence and Nancy Pelosi right up until a bullet ripped through her chest and everyone else went, "Holy fuck, they're shooting white people! We're all going to fucking die!" and the insurrection ended with a single shot.

People like this should never, ever, EVER be allowed to own guns. They aren't going to save the country from tyrants. They're going to start some shit because of a delusional collective fever dream and get themselves and likely innocent people killed.

This is the replacement controller I built for the wheelchair lift. The controller itself is in the middle. The four board on the left and right are a testing harness. The red and black wires are 24VDC and the green and white ones TX and GND for monitoring with a terminal program on my notebook (puTTY).

Without the test harness it looks like this.

I was trying to squeeze a LOT into the BID box that I'm using for this project. I had to stack boards to get everything in.

The bottom most board is a standard bottom board for the BUD case. It has holes along each side for 2.54 screw terminals and pluggable screw terminals. I'm only using that board to mechanically connect the project to the BID case and for the screw terminals. I almost always use pluggable screw terminals because they're awesome. I can unplug four plugs instead of unscrewing 36 screw terminals and trying to keep the wires straight.

There are two top boards. The one on the left carries four relays which turn the negative logic of the Darlingtons into positive logic for the lift. They send 24VDC out to the contactors that run the motors and the door lock. The other small board at the rear has two safety relays which switch power coming in through a bunch of safety switches out to the battery relay and the main contactor.

This is what it looks like assembled into its BUD case.

This is all built around an Arduino Nano with a program that I wrote in Great Cow BASIC.

I'm working on replacing the Schneider SmartRelay on an Atlas Vista 613 wheelchair lift that I bought for my dad. The Atlas technician agrees that the SmartRelay is probably shot and the replacement is $1,000 wholesale. I built a replacement using an Arduino Nano, a UNL2803A Darlington array, a switching 7805, a bunch of Zener diodes, and a handfull of Schneider industrial relays.

Unfortunately, I let the smoke out of my very last Nano and needed to keep the project moving. So...I took a small piece of protoboard, an Arduino ProMini 168, and some jumper wire and created this Frankenduino. It's the same pinout as the Nano with none of the nice supporting stuff like an ICP port, USB, voltage regulators, etc. It will keep the development moving while I'm waiting for the 10 Nanos I have on order to arrive.

I give you Frankenduino. It's an Arduino ProMini soldered onto a piece of protoboard and wired up to the Nano pinout.

I have 10 Nanos on order but I really needed to keep the project moving.

This ProMini has an ATMEGAS168 chip on it but that's good enough for what I'm doing.

My wife made potato salad to bring to dinner at friends' house last night. It's about half hard boiled duck eggs by volume.

Delicious!

We were invited friends house for dinner last night. My wife brought potato salad. I like lots of eggs in my potato salad. We had a couple of dozen duck what in the fridge so my wife boiled up a dozen and added them. It's about half by volume hard boiled duck eggs and it's delicious.

For two or three weeks each spring and fall it gets very noisy on the homestead.