JustEnoughDucks

In Belgium, we are forced by law to use Cca data cables because of "lower fire risk" while I hear literally everywhere that CCA data cables have a much higher fire risk.

Everything here has to comply with the euroclass chart level cca or higher which is confusing because they seem to be combustibility(ca) ABCDEF rating. Making the minimum required in Belgium (and the most prevalent) Cca.

I think for example that getting this for PoE (sorry, in Dutch) would be fine because it does say that it is pure copper, but it also says that it is CCA which is confusing.

Not really a question or anything, just very confusing considering Cca and Eca are the 2 cable types used for residential homes which happen to correspond also to Copper clad aluminum and Enhanced Circuit Integrity. Adds extra probably completely unnecessary stress.

Hey everyone,

There is no real "homenetworking" community like there was on reddit so I thought I would try my luck here.

I live in a 130m^2 house (~1500sqft) that is being completely stripped. That means I am putting in 12-14 Ethernet jacks in the rooms that might need it and have to completely redo my home network setup.

It is a house from the 1950s in belgium, so 21cm thick internal brick walls, a bit thicker concrete floors on the 2 levels. It is essentially a square (8m x 9m outer dimensions), and most of the advice on the internet is built for sprawling American wood houses which have completely different absorption of wireless signals. It has central stairs and essentially 4 rooms, 2 on either side with the kitchen in the back being bigger.

The little advice that I have seen is "brick walls -> get a bunch of access points" but that doesn't sit right with me.

1. Currently we are using a Proximus (our ISP) modem/router in the northwest most far corner or the house and still get weak signal (enough for lower quality videos like Instagram reels) all the way in the southeast corner on the 2nd floor. It goes through 2 brick walls, a concrete floor, and a door and we can still use WiFi 6. Intuitively I would then set up something like an Asus rt-ax58u or a zenwifi XT8 mounted to the staircase wall or in the hallway in the center of the house. I don't know if that would be strong enough to reach everything we need, but it seems better to me than a router in each corner and blasting channel noise at our neighbors' houses since in belgium there isn't much side-garden if any.

2. I have a home server running a variety of local and internet-facing services for myself and family. Due to ease of wiring, I would prefer running modem -> TP-SG1SG016DE -> Wireless Router and using an Asus router. Would the TPlink kind-of-managed-switch be able to isolate the modem fron the rest of the network and just run it to my router to use the LAN of the router for the rest of the ports on my switch? It has port isolation functionality, so I assume so. Then I don't have to run double Ethernet to the hall.

I want to go with Asus because I hear that they generally have more features than other brands. I for sure need port forwarding, QoS, disabling PnP, assigning static IP, and NAT loopback if possible so that local access of services doesn't have to go through cloudflare and can go directly to my reverse proxy. My TPlink Archer A7 that I use now can't do NAT loopback and it makes any file transfers limited by my 5:1: asymmetrical upload speed. Also having VLANs for any cameras would be great, but I think you can do something similar via parental controls on an ASUS (restricting a certain device IP's internet access.

Would the Asus rt-ax58u or a zenwifi XT8 have the festures that I would need for my simpleish home server?

Thanks for the help!

Edit: Tl;dr since nobody reads this long of a post:

• I am running Ethernet (cat6) to every room. Modern laptops as well as phones have no Ethernet port, so I need wifi

• I am looking at 1 wireless router, no "mesh" bs at all. The advice of overstuffing a small house full of a dozen access points is overkill and detrimental to performance without power and channel usage tuning.

• I have specific features I want in a router, can one of the listed ones do all of that like NAT loopback?

Hey guys, I have been looking at building a home gym (possibly outdoors) in my new house we are renovating.

I want to get back into lifting as it has been about 4 years since I did it seriously.

I was looking at bars and the market here is ridiculout it seems. I can't find a single stainless steel bar for under 475€($520). The Ohio bar is one of the cheaper ones at 550€ instead of $370. Of course I get why it is more expensive for an import bar, but I literally can't find any bar here non-imported that says that it is stainless steel that isn't calibrated and insanely expensive (550€+)

The difference here betweeen cerakote and stainless is even greater (>100€ in some cases).

I was hoping to just get a second hand rack, some basics weights, and a barbell for around 1000€ or so, but it looks like I would have to spend at least 2000€ to get any kind of setup. Cage here are 850€ or so on the lower end just by themselves.

I am looking at strengthshop.eu, roguefitness.eu, fitness-seller.nl, but I don't really know what are the best bang for your buck options.

It looks like one of those sites has a 340€ stainless steel ATX bar, but I don't know if that is a reliable brand.

Anyone in the EU with any advice?