cecilkorik

I think the hard-right people have mostly self-exiled to their own echo chambers like truth.social and other places that are Donald-used-and-approved. I think he's also active on Twitter again now that Musk has destroyed all content moderation on the platform. They follow their great leader and unless and until he starts posting his demagoguery on Lemmy they have no interest and no reason to come here.

Smartest users are already using OpenShell and don't have anything to fear, at least from this change... for now...

It's not difficult it's just expensive and energy intensive, and frankly boiling water is both cheaper and easier and we've had lots of experience doing it in massive quantities since the steam age and it works great and gives off steam or hot water which can be used for lots more stuff like heating and even power generation. Ice is almost useless in comparison.

As for why you can't freeze salt into ice, they don't mix. It's like trying to mix oil and water. Technically, if you get the ice really really cold and mash it up with some equally cold salt you could make some kind of mixture of ice and salt and maybe even compress it together until it forms a solid mass again, but it's not saltwater ice, it's just salt and ice mixed together like oil and water. They may appear mixed, but they don't mix, they don't dissolve into each other. Ice's crystal structure does not have anywhere for the salt to go and the salt's crystal structure doesn't have anywhere for the ice to go they're not compatible in any way.

Matrix and its implementations like Synapse have a very intimidating architecture (I'd go as far as to call most of the implementations somewhat overengineered) and the documentation ranges from inconsistent to horrific. I ran into this particular situation myself, Fortunately this particular step you're overthinking it. You can use any random string you want. It doesn't even have to be random, just as long as what you put in the config file matches. It's basically just a temporary admin password.

Matrix was by far the worst thing I've ever tried to self-host. It's a hot mess. Good luck, I think you're close to the finish line.

Most cheap non-dimmable LEDs have drivers that use resistors to determine the current to drive through the LEDs. As a rule, these are always set too high to overdrive the LEDs (sometimes as much as twice their rated current) for marginal brightness gains and to burn out the bulb prematurely. I'm obviously unable to actually see directly into the operation of the great minds that design LED lightbulbs but logic leaves me with only those two plausible conclusions, I'll let you decide which motivation you think is a bigger factor for most manufacturers.

Conveniently, most manufacturers carefully fine-tune this value to prematurely destroy the LEDs at just the right time, which requires careful balancing of resistors, and even MORE conveniently (for us) the cheapest way for them to do this is typically to use two resistors. And MOST conveniently (for us), if you were to carelessly break one of the pair of resistors they use, and leave the other one intact, the current would immediately drop to a very reasonable and appropriate level, generating much less heat, drawing much less power, making LED death extremely unlikely, and only modestly reducing brightness in many cases, because LEDs have non-linear brightness and the heavily overdriven ones are typically FAR beyond the point of diminishing returns. In some cases the reduction in power results in basically no visible difference in light output. In some cases it can be argued they're literally stealing extra power from your electricity bill and using it as an electric heater for no purpose other than to burn out your own light bulbs prematurely so you have to replace them.

The good news is, like I said, removing one of the responsible resistors instantly solves the design flaw and is usually quite easy even without any special tools or electronics knowledge. BigCliveDotCom calls this "Doobying" the bulbs after the Dubai bulbs that were mentioned in other comments. If you watch some of his videos about LED bulbs you should be able to see the pattern of which resistors to remove, if they are on the board they will basically always be right next to each other and relatively small values (typically in the 20 ohms to 200 ohms range). The only modification I make to his procedure is that I prefer to remove the HIGHER value of the two resistors instead of the lower one, which results in perhaps somewhat less lifetime preservation (still much more than the original setting) and less power savings, but more brightness, and is usually adequately good for my purposes. I also use sturdy tweezers to remove the resistor instead of a screwdriver which seems to me that it would have a higher risk of collateral damage.

Is it a lot of work for a single light bulb? Kind of, yes. But once you get it done a bunch of times, you'll probably rarely have to do it again, as these bulbs last almost forever. In fact, I have yet to have one actually fail, I am mostly just replacing the occasional old unmodified LED bulb from time to time.

This will not work with dimmable bulbs or certain fancy high end bulbs. Also some are much, much easier to modify than others. Clive calls the ones that are relatively easy "hackable" and it's really a crapshoot to find them. Some have covers/bulbs/diffusers that are nearly impossible to remove without catastrophic damage to the bulb and/or your hands. Others simply use a different circuit design that doesn't have resistors. Some only have a single resistor, meaning to change the value you need to solder a new one in its place. In my experience, the bargain-basement, junkiest, least reliable bulbs tend to be the easiest to hack this way and often skimp on things like "gluing the lens on" so it's easy to get off. But you'll have to experiment to find a brand and style that works well for this.

So it's not really FOSS at all, it's just a loss-leader to draw you into the network, trap your data, and then enshittify and monetize as per standard practice.

I really like what they're doing to GIMP lately and I am looking forward to 3.0!

I would need to factory reset the whole server for that, which would be … highly inconvenient for me. It took me quite a long time to get everything working, and I don’t wanna loose my configuration.

This is your actual problem you need to solve. Reinstalling your server should be as convenient as installing a basic OS and running a configuration script. It needs to be reproducible and documented, not some mystery black box of subtle configurations you've forgotten about ages ago. A nice, idempotent configuration script is both convenient and a self-documenting system for tracking all the changes you've ever implemented on your server.

Once you can do that, adding whatever encryption you want is just a matter of finding the right sequence of commands, testing it (in another docker perhaps) and then running your configuration script to migrate your server into the desired state.