this post was submitted on 09 Aug 2024
17 points (100.0% liked)

3DPrinting

15629 readers
122 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
j4k3@lemmy.world
andypiper@lemmy.world
henry_rowengartner@lemmy.world
GrayBackgroundMusic@lemm.ee
17
Creality K1 Max Curves Surface Issue (sh.itjust.works)
submitted 3 months ago by xzot746@sh.itjust.works to c/3dprinting@lemmy.world
9 comments fedilink hide all child comments
 

I have a K1 Max and mostly it is running great, however I get strange artifacts on mostly only the front side of curved objects.

I have lubed all the rods, and I have a Capricorn PTFE tube from the filament sensor to the hot end. I tried the printable guide for the tube to go into the hot end but it wasn't any better and I thought that was the culprit at first.

I have an extension piece to raise up the top glass.

I'm using Elegoo Rapid PTEG running at 240c and 250mm outerwall speed. This is mainly happening on the front side and anywhere on the build plate. Filament is dry and fed out of the Creality Space dryer.

These items are small netcups but it was also happening on the larger sections that they go in.

Using Orcaslicer and Arachne wall generator.

Any ideas where I need to be focusing my attention on?

you are viewing a single comment's thread
view the rest of the comments
[–] xzot746@sh.itjust.works 2 points 3 months ago (1 children)

Thanks for your reply, to your point yes they still fit, been having this issues for a bit now as I'm up to about 40 of these netcups and the associated other pieces for the grow towers.

I think the belts are good, but will double check.

[–] FuglyDuck@lemmy.world 2 points 3 months ago (1 children)

to clarify, other parts that aren't related to the model, do they print fine? or is it just these pairs of models?

it could be the mesh you're dealing with is corrupted.

[–] xzot746@sh.itjust.works 1 points 3 months ago (1 children)

Good point, I have mainly been printing these items for the hydroponic tower. I do have other versions that I can check. I think after this set prints I will add some basic shapes in different orientations to see if there is issues still.

That being said I did print some other items that were stacked and each one is much thinner but there are no artifacts on the outer walls.

[–] Krackalot@discuss.tchncs.de 2 points 3 months ago (1 children)

Could try rotating the model 90°. If the issues remain in the same location, you'll know it's a printer issue, maybe due to the size of the radius.

[–] xzot746@sh.itjust.works 2 points 3 months ago (1 children)

So I sliced and printed a different model, and then rotated 1 by 180°, it is somewhat weird as the lowest part on the right model seems ok but as the wall built up on the inside it was getting the artifacts. The model on the left was getting the artifacts on the outer piece but not the inner.

In rotating the models after, the artifacts are on the opposite side.

I noticed it was starting at the seam, I have the scarf joint on contour, and noticed that "scarf around entire wall" was checked so trying reprinting to see if that is the issue.

[–] xzot746@sh.itjust.works 1 points 3 months ago

Well that was the problem, thanks for everyone's input.